DC-SWAT Forum

Полная версия: Коврик для DDR своими руками...
Вы просматриваете yпpощеннyю веpсию форума. Пеpейти к полной веpсии.
Все прекрасно знают, что найти сейчас в продаже коврик для такой замечательной игрухи как Dance Dance Revalution большая проблема. Даже на ebay уже стала проблема найти его и там. И так предлагаю Вам инструкцию как переделать джойпад дрима под ковер (инглишь естесно) )

Цитата:Materials: omni folder (paper folder or some sort of thin tough flexible material)Eight thin pieces of metalLots of wireThick piece of corrugated cardboard. (like from a box)Paper towelsElectrical tape.Spare Dreamcast controllerSafety Pin (not used as a part of the final product it just helps to have one handy)

Step 1. First cut out eight 1 1/2”x 4” pieces of the folder

Step 2. Next take the small thin pieces of metal and solider or wrap a wire around them.

Step 3. Take a paper towel and make a small roll. About the size of your thumb.

Step 4. Tape the thin pieces of metal in the middle of all of the 1 1/2x4 pieces of thin cardboard.

Step 5. Make four of the things that looks like this out of the rolled up paper towels the 1 1/2x4 pieces of cardboard with the metal on them and tape them together.

[Изображение: image001.jpg]

[Изображение: sega-dc-pcb.jpg]

**make sure that when you press down on the “pad” that the two thin pieces of metal make contact with one another.**

Step 6

. This is the tricky part, take the spare dc controller apart. Be careful to not destroy anything. The little blue circles with the dot in the middle is your target. Take the safety pin and poke at the middle of the blue circles this is just to make it so you can fit a small wire through them. For the DDR pad we're just going to use the ↑ ↓← and →.

Step 7. After poking the holes with the safety pin run a small wire through the hole. Color coding your wires at this step would really make things go easier later on.

Step 8. After running the wires through the holes you can either solider them on the opposite side or place a piece of electrical tape over them so they don't go any where.

Step 9. Now it's time to find a way to get the wires that you just placed on the controller board out of the controller. The only way I can suggest is to cut a small notch under where the chord for the controller comes out.

Step 10. This is the step where color coding wires will be helpful. Once you have the wires out of the controller, hook your common ground up like so on the bottom of the piece of corrugated cardboard.


[Изображение: image003.jpg]

Step 11. After connecting the common d-pad ground to the bttom of the foot pads, connect the wires from the directional pad (up down left and right) to the top half of the foot pads.

[Изображение: image006.jpg]

Step 12. cut notches to put the pads through the cardboard so you don't have wires hanging on the top of you dance mat.

Step 13. the finial step is to test out your work load up DDR in training mode pick any song and look up at the arrows. When you hit the direction the arrow should jump. You'll know it when you see it.

Step 14. I didn't want to end up with 13 steps so the real final step is to have fun and never stop modding!

[Изображение: HPIM0448.jpg]

[Изображение: HPIM0449.jpg]


оригинал:devcast.com
Картинки не сохранились?
Проще прямой линк было кинуть
Оригинальной статьи уже и не осталось в первоисточнике.

Да нужно было картинки на дс-сват залить, но наверное в лом было или не догадался...

Оригинал находился тут
http://dev.dcemulation.com/tutorials.htm
Цитата:Картинки не сохранились?
Сохранились.

Цитата:Оригинал находился тут
http://dev.dcemulation.com/tutorials.htm

Как ты знаешь, dcemulation.com "переехал" на dcemulation.org, поэтому статью искать надо было там.
Вот собственно она:
http://devcast.dcemulation.org/mods/ddrmat/ddrmat.php
Обновил пути картинок. Спасибо Василий
URL ссылки