Создать ответ 
 
Рейтинг темы:
  • Голосов: 0 - Средняя оценка: 0
  • 1
  • 2
  • 3
  • 4
  • 5
No GD-ROM, Can't read MBR from IDE by LBA
Автор Сообщение
polyfusion Не на форуме
Новичок
*

Сообщений: 6
Зарегистрирован: 21.07.2014
Рейтинг: 0
Сказал спасибо: 1
Поблагодарили 1 раз(а) в 1 сообщ.
Сообщение: #1
No GD-ROM, Can't read MBR from IDE by LBA
Trying to get this to work, hoping someone can provide some guidance...

Have a XCKDIY board with a 2.5 HDD mounted onto it. It has an oscillator (and a resistor) already attached.

The Dreamcast has the "boot_loader_unlock_G1_IGR_dbs_nogdrom.bios" flashed, and I believe it's ok, as I get the DEV bootscreen, and Dreamshell then loads ok from the SD card.

However, in the bootup screen, I can see the message:

Checking for G1 ATA devices...
Can't read MBR from IDE by LBA

Then some messages relating to the loading of the SD card, which it then does sucessfully.

When I go into ISO loader, the HDD isn't available to select.

The HDD was formatted in FAT32, and I have a DS folder loaded to the root of the HDD. I put the megavolt85 "DS_CORE.BIN" file on the root of the DS folder, and removed other BIN files from the root.

I think I followed the same as pstationBG in this thread:

http://www.dc-swat.ru/forum/printthread.php?tid=2250

Anything else I should try?

Thanks.
30.04.2016 12:18
Найти все сообщения Цитировать это сообщение
 Сказали спасибо: jacobsson
polyfusion Не на форуме
Новичок
*

Сообщений: 6
Зарегистрирован: 21.07.2014
Рейтинг: 0
Сказал спасибо: 1
Поблагодарили 1 раз(а) в 1 сообщ.
Сообщение: #2
RE: No GD-ROM, Can't read MBR from IDE by LBA
I got it working, I was looking at some photos of HDD's people were using in their DCs, and could just about make out that they were jumpered. So I put a jumper on the two pins that looked like it needed it, and it works great now.

Also, I see 3 solder points which look like they are in the right location for the DCs lid switch. Had anyone installed a switch, and advantage/disadvantage to doing so?

Many thanks to everyone who made this happen.
30.04.2016 15:42
Найти все сообщения Цитировать это сообщение
megavolt85 Не на форуме
Супермодератор
******

Сообщений: 3065
Зарегистрирован: 24.03.2012
Рейтинг: 37
Сказал спасибо: 179
Поблагодарили 1510 раз(а) в 893 сообщ.
Сообщение: #3
RE: No GD-ROM, Can't read MBR from IDE by LBA
Use Acronis Disk Director
1) Remove partation from HDD
2) Create primary partation on HDD
3) Format to FAT32

HKT-3030, Bios mod, SD mod, VGA internal mod, G1ATA mod, Region changer mod, PSU mod
30.04.2016 15:46
Найти все сообщения Цитировать это сообщение
jacobsson Не на форуме
Пользователь
**

Сообщений: 40
Зарегистрирован: 28.04.2016
Рейтинг: 0
Сказал спасибо: 49
Поблагодарили 5 раз(а) в 4 сообщ.
Сообщение: #4
RE: No GD-ROM, Can't read MBR from IDE by LBA
(30.04.2016 15:42)polyfusion писал(а):  I got it working, I was looking at some photos of HDD's people were using in their DCs, and could just about make out that they were jumpered. So I put a jumper on the two pins that looked like it needed it, and it works great now.

Also, I see 3 solder points which look like they are in the right location for the DCs lid switch. Had anyone installed a switch, and advantage/disadvantage to doing so?

Many thanks to everyone who made this happen.

Hi! I just dusted off my XCKDIY HDD adapter and I remember last time I tested it that I never got I working (with a known working drive pulled from my soldered G1-ATA SATA mod). It halted on the init-screen for G1-ATA and SD devices.
What pins did you add a jumper between? Thanks a lot for your answer!
(Последний раз сообщение было отредактировано 08.05.2017 в 15:35, отредактировал пользователь jacobsson.)
08.05.2017 12:58
Найти все сообщения Цитировать это сообщение
Создать ответ 


Похожие темы
Тема: Автор Ответов: Просмотров: Посл. сообщение
Лампочка Sturmwind Fix Read Error dragoncity 23 32344 31.01.2022 14:53
Посл. сообщение: fafadou

Переход:


Пользователи просматривают эту тему: 1 Гость(ей)