Создать ответ 
 
Рейтинг темы:
  • Голосов: 0 - Средняя оценка: 0
  • 1
  • 2
  • 3
  • 4
  • 5
replace Gd-Rom's flat cable
Автор Сообщение
chth96 Не на форуме
Пользователь
**

Сообщений: 67
Зарегистрирован: 12.04.2015
Рейтинг: 0
Сказал спасибо: 14
Поблагодарили 19 раз(а) в 15 сообщ.
Сообщение: #1
replace Gd-Rom's flat cable
Yesterday,My dreamcast suddenly cannot recognize any GD or CD-R media..(It spinned up and checked any media but it only stayed at the start menu.. won't start any dreamcast game or application)
I measured resistance value of Laser Lens by putting multimeter's red probe and black probe on 1 and 2 pin of ribbon cable connector which located on the back of Gd-Rom pickup's PCB. and to my surprise, It measured more than 1M ohm..
I fiddle with small pot of Laser Lens..But measured resistance value won't drop to less than 300k ohm..
I noticed that It has something wrong with Laser Lens or flat cable,So I put multimeter's red probe and black probe on each end of flat cable,and I finally found that 1 pin of flat cable have been break..
[Изображение: 20210515-235357-1.jpg]

I took advantage of broken DVD-RW which has wide and strong flat cable and I cut this strong flat cable into almost same width(16 pin) and height with Gd-Rom's flat cable as possible as I can..
and scratched one end of strong flat ribbon cable with knife in order to expose all 16 pin of metallic conductors .
then,I strip off blue stiffener from cut off strong ribbon cable and insert this blue stiffener together with one end of strong flat ribbon cable..

[Изображение: 20210515-235125-1.jpg]
It is somewhat hard to insert one end of strong flat ribbon cable and blue stiffener together into connector of Laser Lens. But without blue stiffener, It is impossible to steady strong flat ribbon cable in connector of Laser Lens..

Now,My dreamcast really works very well to read any CD-R or GD media like before..
I think that If Your Gd-Rom's flat cable is broken and has CD-RW or DVD-RW which have wide flat ribbon cable then you don't have to purchase any dreamcast's ribbon cable of below ebay link..
https://www.ebay.com/itm/280801156507
(Последний раз сообщение было отредактировано 15.05.2021 в 20:50, отредактировал пользователь chth96.)
15.05.2021 20:22
Найти все сообщения Цитировать это сообщение
megavolt85 Не на форуме
Супермодератор
******

Сообщений: 3064
Зарегистрирован: 24.03.2012
Рейтинг: 37
Сказал спасибо: 179
Поблагодарили 1509 раз(а) в 892 сообщ.
Сообщение: #2
RE: replace Gd-Rom's flat cable
you just don't need to look for a loop for dreamcast, then the price will be adequate Big Grin

select 10cm, A-type, 16P an look price for 10 pcs

HKT-3030, Bios mod, SD mod, VGA internal mod, G1ATA mod, Region changer mod, PSU mod
16.05.2021 11:55
Найти все сообщения Цитировать это сообщение
 Сказали спасибо: chth96
chth96 Не на форуме
Пользователь
**

Сообщений: 67
Зарегистрирован: 12.04.2015
Рейтинг: 0
Сказал спасибо: 14
Поблагодарили 19 раз(а) в 15 сообщ.
Сообщение: #3
RE: replace Gd-Rom's flat cable
(16.05.2021 11:55)megavolt85 писал(а):  you just don't need to look for a loop for dreamcast, then the price will be adequate Big Grin

select 10cm, A-type, 16P an look price for 10 pcs

the flat ribbon cable of your link is reasonable price. and I think 6cm length would be more suitable than 10cm,Because length of GD-ROM's original flat ribbon cable is 7cm and I noticed that if length of flat ribbon cable is more than 7.5cm, laser lens cannot read the most outer space of CD-R or GD media.
https://ibb.co/yXg3fnz

If length of flat ribbon cable is 10cm,then surplus length of ribbon cable(3cm) would get in the way of laser lens to reach the outermost position.
(Последний раз сообщение было отредактировано 16.05.2021 в 16:55, отредактировал пользователь chth96.)
16.05.2021 15:36
Найти все сообщения Цитировать это сообщение
megavolt85 Не на форуме
Супермодератор
******

Сообщений: 3064
Зарегистрирован: 24.03.2012
Рейтинг: 37
Сказал спасибо: 179
Поблагодарили 1509 раз(а) в 892 сообщ.
Сообщение: #4
RE: replace Gd-Rom's flat cable
the extra three centimeters are bent near the connector on the drive board and the cable fits perfectly, it has been proven more than once Wink

HKT-3030, Bios mod, SD mod, VGA internal mod, G1ATA mod, Region changer mod, PSU mod
16.05.2021 19:49
Найти все сообщения Цитировать это сообщение
Создать ответ 


Похожие темы
Тема: Автор Ответов: Просмотров: Посл. сообщение
  1080p using VGA cable: KOF 99 EVOLUTION Dreamcast. aldair 0 1202 28.01.2023 12:00
Посл. сообщение: aldair
  Acer 2020_2021 monitors with 240p Native on VGA Dreamcast cable. aldair 1 2779 21.11.2021 02:14
Посл. сообщение: aldair
  240p working on VGA cable. aldair 0 2717 26.09.2021 17:29
Посл. сообщение: aldair
  Link Cable Dreamcast-connection from A to B. aldair 0 3243 05.02.2021 12:34
Посл. сообщение: aldair
  Dreamcast link cable: Connector aldair 0 3697 20.01.2021 15:32
Посл. сообщение: aldair
  USB-Serial Dreamcast Codes Cable aldair 0 3821 10.11.2020 22:00
Посл. сообщение: aldair
  how to transfer save using coder cable? aldair 0 3498 08.11.2020 02:18
Посл. сообщение: aldair
  HDMI, VGA and AV all in one cable / Dreamcast aldair 0 3556 16.09.2020 18:51
Посл. сообщение: aldair
  HDMI Link Cable for Dreamcast by Pound Technology Ivan Guber 5 14281 06.06.2018 12:39
Посл. сообщение: Toe-Knee
Грустный Don't boot anymore if you cut the ide cable... dragoncity 15 26463 10.05.2018 19:39
Посл. сообщение: fanhais

Переход:


Пользователи просматривают эту тему: 1 Гость(ей)