Создать ответ 
 
Рейтинг темы:
  • Голосов: 0 - Средняя оценка: 0
  • 1
  • 2
  • 3
  • 4
  • 5
Freezing at bootloader with StarTech adapter
Автор Сообщение
Mu. Не на форуме
Пользователь
**

Сообщений: 41
Зарегистрирован: 05.01.2019
Рейтинг: 0
Сказал спасибо: 4
Поблагодарили 4 раз(а) в 4 сообщ.
Сообщение: #1
Freezing at bootloader with StarTech adapter
I'm attempting to use the StarTech IDESAT2 SATA adapter (the red PCB) and a 120GB hard disk with Dreamshell. I'm finding that the bootloader will recognise the disk properly will also show up as a selectable option in the boot menu however in both cases it will immediately freeze the console whenever it attempts to boot.

I have tried with pin 1 connected, floating and grounded via a 10k resistor as has been recommended before but nothing seems to work.
05.03.2020 05:35
Найти все сообщения Цитировать это сообщение
fafadou Не на форуме
Опытный
****

Сообщений: 857
Зарегистрирован: 07.03.2017
Рейтинг: 1
Сказал спасибо: 1129
Поблагодарили 89 раз(а) в 82 сообщ.
Сообщение: #2
RE: Freezing at bootloader with StarTech adapter
Are you sure you are in slave mode ?
Disk format in fat 32, 64ko cluster.
Try without any pin 1.
05.03.2020 12:21
Найти все сообщения Цитировать это сообщение
Mu. Не на форуме
Пользователь
**

Сообщений: 41
Зарегистрирован: 05.01.2019
Рейтинг: 0
Сказал спасибо: 4
Поблагодарили 4 раз(а) в 4 сообщ.
Сообщение: #3
RE: Freezing at bootloader with StarTech adapter
Disconnecting pin 1 allowed it to boot to Dreamshell, as long as I press start and select the device. Automatic booting didn't work. Neither does 0.7.0 ISO loader, it says the following:

DreamShell ISO from IDE loader v0.7.0
Initializing IDE...
Can't init IDE
Error, can't init IDE.
Failed!.
05.03.2020 22:47
Найти все сообщения Цитировать это сообщение
fafadou Не на форуме
Опытный
****

Сообщений: 857
Зарегистрирован: 07.03.2017
Рейтинг: 1
Сказал спасибо: 1129
Поблагодарили 89 раз(а) в 82 сообщ.
Сообщение: #4
RE: Freezing at bootloader with StarTech adapter
In IDE you must have the DS folder too same as sdcard, on root the IGR folder with DS_CORE.BIN and in order to be sure the DS_CORE.BIN on the root too. I did like that.
Running games with v0.7.0 must have a defragmented drive, use defraggler for your HDD.

If you use a sata drive I don't know what model works, but with ssd : samsung and crucial works well.

For me, when I'm reading your error message is a welding error, only pin 2 as short as possible if you don't use a pcb, max 5cm for 0.7.x.
It works with an other IDE to SATA converter ?

Hope you will be able to run this IDE to SATA converter, it looks like a very good model, may you would run visual concept games with it.
It's a good thing you are trying :-)
06.03.2020 12:16
Найти все сообщения Цитировать это сообщение
 Сказали спасибо: linerty
Mu. Не на форуме
Пользователь
**

Сообщений: 41
Зарегистрирован: 05.01.2019
Рейтинг: 0
Сказал спасибо: 4
Поблагодарили 4 раз(а) в 4 сообщ.
Сообщение: #5
RE: Freezing at bootloader with StarTech adapter
I can't say whether or not I have my DS folder layout set exactly as you outlined it at the moment with DS_CORE.BIN in the appropriate places. However I know that it is set up the same as when I was using a CF card (which worked perfectly).

I also know that my drive has absolutely no fragmentation, I believe the 0.7.0 loader would warn me of this if I did and I can confirm in Defraggler that this isn't an issue.

I'm using a generic 120GB Toshiba hard disk which could be the issue for all I know. I have other drives I can test with so I'll get back to you on this one.

As for the soldering, I am using Dragoncity's G1-ATA adapter board so I presume pin 2 is an appropriate length. And my generic adapter (chip is labelled B75TT0041, no results online) doesn't work any better. I'll pick up the JM20330 adapters others have tried and used as well for experimentation. I'm happy to spend some money to share my experiences and knowledge with everyone else should it be of any value to anyone.
07.03.2020 06:19
Найти все сообщения Цитировать это сообщение
fafadou Не на форуме
Опытный
****

Сообщений: 857
Зарегистрирован: 07.03.2017
Рейтинг: 1
Сказал спасибо: 1129
Поблагодарили 89 раз(а) в 82 сообщ.
Сообщение: #6
RE: Freezing at bootloader with StarTech adapter
If you can try a JM20330, you'll see if the issue is adapter or your hdd.
07.03.2020 11:23
Найти все сообщения Цитировать это сообщение
Mu. Не на форуме
Пользователь
**

Сообщений: 41
Зарегистрирован: 05.01.2019
Рейтинг: 0
Сказал спасибо: 4
Поблагодарили 4 раз(а) в 4 сообщ.
Сообщение: #7
RE: Freezing at bootloader with StarTech adapter
Strangely the issue appears to be neither. I set up a new drive and got it to work just fine with the 0.7.0 loader and boot directly without going to the boot menu. I switched back to the 120GB Toshiba and it did the same thing. Everything works as it should now and I have no clue why Big Grin
07.03.2020 22:07
Найти все сообщения Цитировать это сообщение
 Сказали спасибо: fafadou
fafadou Не на форуме
Опытный
****

Сообщений: 857
Зарегистрирован: 07.03.2017
Рейтинг: 1
Сказал спасибо: 1129
Поблагодарили 89 раз(а) в 82 сообщ.
Сообщение: #8
RE: Freezing at bootloader with StarTech adapter
Sometimes there is some mystery ^^
Have you notice some differences ? Have you tried some visual concept games ?

EDIT the complete list of games ok in ide and not with ssd JM20330 adapter :

Floigan Bros. - Episode 1
Geist Force
NBA 2K
NBA 2K1
NBA 2K2
NCAA College Football 2K2 - Road to the Rose Bowl
NFL 2K
NFL 2K1
NFL 2K2
Ooga Booga
San Francisco Rush 2049 (Rush 2049)
Toe Jam And Earl 3

Try some please.
(Последний раз сообщение было отредактировано 09.03.2020 в 17:08, отредактировал пользователь fafadou.)
08.03.2020 05:41
Найти все сообщения Цитировать это сообщение
Создать ответ 


Похожие темы
Тема: Автор Ответов: Просмотров: Посл. сообщение
  Dreamshell + SD card Serial Adapter state_product 0 1194 01.09.2023 19:30
Посл. сообщение: state_product
  Sata hdd issues, jp 103-5 adapter shefben 4 4749 12.07.2022 02:59
Посл. сообщение: fafadou
  This IDE-SATA adapter would work in Dreamshell? Ro Magnus Larsson 2 3352 09.06.2022 09:42
Посл. сообщение: Ro Magnus Larsson
  VGA to HDMI adapter with interference. aldair 0 2275 12.11.2021 02:31
Посл. сообщение: aldair
Грустный DC freezing after mounting G1-ATA Nold 4 11252 30.01.2018 13:34
Посл. сообщение: jacobsson
  DC with MGCD jamma adapter aykiri1 0 5372 27.05.2017 16:50
Посл. сообщение: aykiri1
  How to play game discs directly on a bootloader? Poknatus 3 10577 26.04.2017 09:38
Посл. сообщение: Poknatus
  SATE to PATA/IDE Hard Drive Adapter(Dreamcast) aldair 0 6655 29.08.2016 02:12
Посл. сообщение: aldair
  Speed test_ ide-sata adapter on the sega dreamcast aldair 0 6244 06.08.2016 02:01
Посл. сообщение: aldair
  IDE-SATA adapter in GD-ROM Dreamcast aldair 1 8023 03.08.2016 01:05
Посл. сообщение: megavolt85

Переход:


Пользователи просматривают эту тему: 1 Гость(ей)